Sunday, May 17, 2009
How Do I Clean My Airsoft Gun?
Although in many cases, the internals are where the most cleaning needs to be done, this guide is intended to answer questions about the barrel of the airsoft gun only and is geard towards the "newbie" level player.
For those of you hoping to get info on cleaning the guts of the gun (I.e. the mechbox or valve assembly) I would strongly encourage you to take a look at either www.mechbox.com or the newer but promising www.airsoftdna.com. These sites will show you how to disassemble the guns to their individual components and cleaning is then simply a matter of you using your best judgment on how best to wipe the parts clean.
On to the guide!
There are a couple of different ways to clean an airsoft gun barrel but they all do the same thing; clean gunk off the inside of the smooth barrel which is in the airsoft gun. Because airsoft guns (usually) don't have rifled barrels (Barrels with spiral grooves cut into the inside of the barrel) you will not have to worry about getting crud out of these grooves. This means that the cleaning process is pretty simple. Basically, you are going to need to swab out the barrel using some oil and a cleaning patch (small square of fabric or paper). Bear in mind that the barrel of an airsoft gun is quite small (narrow diameter) and therefore, I have found that the best method of pushing the cleaning patch through the barrel is to use an airsoft cleaning rod. Generally, these rods come with the gun and are usually plastic. The plastic construction helps to prevent damaging the barrel and other parts on the and I would advise against using metal coat hangers or similar.
Before you get started, here are a couple of things to keep in mind:
ALWAYS, ALWAYS THINK SAFETY! This means making sure that your airsoft gun is completely unloaded, de-charged, de-gassed, de-cocked etc...
Once you've made sure the airsoft gun is safe begin the cleaing process:
#1 Turn the hop up off. That is, turn the hop up to the setting where the is NO back spin on the bbs. IF you don't do this, you risk damaging the hop up bucking with the cleaning patch/rod.
# 2 tear off a small piece of paper towel (approx. 1"x1") and bend it in half so it looks like a triangle. Thread one corner of the triangle through the eye (the slit) in the tip of the cleaning rod.
#3 Lubricate the cleaning patch with a few drops of silicone oil (DO NOT USE WD40!!!! as it can erode the rubber in the hop up and on the rest of the gun!!!)
#4 Using steady pressure, push the cleaning rod through the barrel from the tip of the barrel to the feed port of the gun. (I usually tip the gun on its back to see if the cleaning rod has reached the feed tube.) DO NOT APPLY TOO MUCH PRESSURE! if you feel an obstruction in the barrel, be VERY careful to make sure that the obstruction is a BB or something else. IF you feel the cleaning rod catch on something and you do not see the cleaning rod through the feed tube, you may have caught the hop up bucking and pushing too hard could ruin the bucking.)
#5 Once you've pushed the rod all the way down the barrel, pull it out and inspect it for dirt or other particulates. If the patch (the small piece of paper towel) is dirty, then remove it and replace it with a fresh cleaning patch, re-lubricate and repeat the cleaning process till the cleaning patches no longer come out of the barrel dirty.
If you follow these steps and use your common sense, you will be able to successfully, clean nearly any airsoft barrel.
Wednesday, March 4, 2009
Classic Army P90 Sportline TR with Metal Receiver
What sweetened the deal even more was the offer to include a metal receiver upgrade for me to take a look at. The P90 SL TR by itself is pretty slick and the heft that the metal upper receiver and rail system adds makes the gun feel really great. Bear in mind that at$85-$90 the metal upgrade isn't the cheapest part to buy, but its not as expensive as some rail kits I've seen.
Playing with the gun wasn't all roses and kittens however. As this model is a "Sportline" unit, there was a fair amount of average feeling plastic body work. I could look past the plastic finish, but what really bugged me was the seem which ran down the middle of the gun. The problem was that the seem created a ridge in both the handholds and caused some chaffing and scratches to my hands.
Luckily the fix was simple, quick and effective. I simply took an exacto and shaved down the portions of the seem where my hand came into contact with it. I am sure a bit of sand paper or a file would achieve a similar result.
In these pictures you can see the seem along with the fire selector switch and the hop up access port. The fire selector worked fine and clicked through its positions well. Interestingly I noticed that when the gun was in full auto mode the trigger could be consistently manipulated to fire in single fire much like the Steyr AUG (Pull the trigger in slightly for single fire and all the way for full auto). The hop was a little difficult to get to, but it hasn't yet required frequent adjustment so it did not concern me too much.
The next problem area was a bit more important to the gun's functionality. The high cap magazine was finicky and required several hard smacks during the preliminary firing tests to cycle properly.
Additionally, the mag would sometimes unwind because the bbs had gotten stuck in the reservoir and this required that the entire mag be removed and rewound. This problem is undoubtedly due to the P90's design which places the magazine in a horizontal position.
I don't fault CA per se as it seems to be part and parcel to the airsoft gun that is the P90. It would seem that, for these reasons, the average P90 skirmisher would do well to pick up some more conventional spring powered low or possibly high cap mags.
Although obvious, another feature I liked was how well integrated the stock is with the rest of the gun. It made the gun feel very solid. Removal of the butt plate requires that you press the small button on the underside of the butt plate.
Once the plate is removed, a very modest battery compartment is exposed that could accommodate only a conventionally shaped 8.4v 1100 mah bat. or a custom fitted battery.
We have not yet completed our full firing tests, but the preliminary results look promising. The ROF with the stock 8.4v 1100 mah battery seem to be above average and the FPS has been clocked as high as 380. One strange thing about our test gun was the inconsistency of the bb velocity. A couple of shots would register around 330 and the next couple would spike to around 380 fps. This is a sportline model, so there may be some loose ends within the gearbox, but it is still strange to see such a variation in the velocity.
The accuracy has been good however, so whatever velocity spikes there are they don't seem to produce many flyers. I got tight groupings out to 100' with ease and I expect good performance when we start pushing this little gun's outer range limitations.
Thus, while our testing is not complete, there are some good and bad things to be aware of if you are in the market for a P90.
To see an excellent review of the CA P90 take a look at this review from Airsoftreview.net
For a great video on how to disassemble the P90 take a look at this guide from mechbox.com.
Privacy Policy
Privacy
Airsoft Reports respects your privacy.
Any personal information you provide to us including and similar to your name, address, telephone number and e-mail address will not be released, sold, or rented to any entities or individuals outside of Airsoft Reports.
Credit card details
Airsoft Reports will never ask for Credit Card details and request that you do not enter it on any of the forms on Airsoft Reports.
External Sites.
Airsoft Reports is not responsible for the content of external internet sites. You are advised to read the privacy policy of external sites before disclosing any personal information.
Cookies
A "cookie" is a small data text file that is placed in your browser and allows Airsoft Reports to recognize you each time you visit this site(customisation etc). Cookies themselves do not contain any personal information, and Airsoft Reports does not use cookies to collect personal information. Cookies may also be used by 3rd party content providers such as newsfeeds.
Google Interest Based Advertising
* Google, as a third party vendor, uses cookies to serve ads on your site. * Google's use of the DART cookie enables it to serve ads to your users based on their visit to your sites and other sites on the Internet. * Users may opt out of the use of the DART cookie by visiting the Google ad and content network privacy policy.Remember The Risks Whenever You Use The Internet
While we do our best to protect your personal information, we cannot guarantee the security of any information that you transmit to Airsoft Reports and you are solely responsible for maintaining the secrecy of any passwords or other account information. In addition other Internet sites or services that may be accessible through Airsoft Reports have separate data and privacy practices independent of us, and therefore we disclaim any responsibility or liability for their policies or actions.
Please contact those vendors and others directly if you have any questions about their privacy policies.
For any other information email webmaster